GCV Error for a newbie on WIN 10
11 posts
• Page 1 of 2 • 1, 2
GCV Error for a newbie on WIN 10
Hello Gentlemen, sorry to bother you but I really need help.
First of all I want to clarify that I have no notion of programming, even very small .... however by trying to understand by switching from forums to google searches, I finally managed to install Python 3.9 and CV in the folder sites-packages as well as pywin32 or numpy . I encountered a lot of problems at different stages (nothing surprising considering my level) but I managed to get around them all. I finally managed to get this step clear
then I tried to set up computer vision in Gtuner IV, i use Xbox stream companion with series X , following the recommandations in the dedicated post
but when i try to make start in CV i have this error,
so I check if it was properly installed by doing it and obviously everything is in order
and honestly, I try to turn the problem in all sides, I can not get away with it ..
Could a good soul help me please ?
Thx by advance
First of all I want to clarify that I have no notion of programming, even very small .... however by trying to understand by switching from forums to google searches, I finally managed to install Python 3.9 and CV in the folder sites-packages as well as pywin32 or numpy . I encountered a lot of problems at different stages (nothing surprising considering my level) but I managed to get around them all. I finally managed to get this step clear
then I tried to set up computer vision in Gtuner IV, i use Xbox stream companion with series X , following the recommandations in the dedicated post
but when i try to make start in CV i have this error,
so I check if it was properly installed by doing it and obviously everything is in order
and honestly, I try to turn the problem in all sides, I can not get away with it ..
Could a good soul help me please ?
Thx by advance
-
belpoutre - Staff Sergeant
- Posts: 11
- Joined: Mon Apr 23, 2018 3:25 pm
Re: GCV Error for a newbie on WIN 10
Hi, this error:
How it translates to English?
Thanks.
How it translates to English?
Thanks.
ConsoleTuner Support Team
-
J2Kbr - General of the Army
- Posts: 20323
- Joined: Tue Mar 18, 2014 1:39 pm
Re: GCV Error for a newbie on WIN 10
J2Kbr wrote:Hi, this error:
How it translates to English?
Thanks.
Hi thx for help , i try to translate as i could ^^
something like that : « a failed dynamic link library (DLL) initialization routine »
-
belpoutre - Staff Sergeant
- Posts: 11
- Joined: Mon Apr 23, 2018 3:25 pm
Re: GCV Error for a newbie on WIN 10
try a lower pywin32 version: 227
run from within your python scripts directory:
run from within your python scripts directory:
- Code: Select all
pip install pywin32==227
-
Scachi - Brigadier General
- Posts: 3044
- Joined: Wed May 11, 2016 6:25 am
- Location: Germany
Re: GCV Error for a newbie on WIN 10
ok i'm looking at this and i will keep you informed thx
-
belpoutre - Staff Sergeant
- Posts: 11
- Joined: Mon Apr 23, 2018 3:25 pm
Re: GCV Error for a newbie on WIN 10
well, finally back home. So I tried the procedure and hope to have done it correctly
but unfortunately exactly the same result
but unfortunately exactly the same result
-
belpoutre - Staff Sergeant
- Posts: 11
- Joined: Mon Apr 23, 2018 3:25 pm
Re: GCV Error for a newbie on WIN 10
try with python 3.8 instead of python 3.9, using a new clean python install
I am using
python 3.8.1
opencv-python 4.2.0.32
pywin32 227
I am using
python 3.8.1
opencv-python 4.2.0.32
pywin32 227
-
Scachi - Brigadier General
- Posts: 3044
- Joined: Wed May 11, 2016 6:25 am
- Location: Germany
Re: GCV Error for a newbie on WIN 10
ok i could try , i didn't think 3.9 could be a problem but i'm exploring all leads so : GO ... let’s doing that ^^
-
belpoutre - Staff Sergeant
- Posts: 11
- Joined: Mon Apr 23, 2018 3:25 pm
Re: GCV Error for a newbie on WIN 10
Thx a lot Scachi :
Now i just need to understand all the information in the 35 pages of this topic [GCV/GPC] Apex Legends CV Anti-Recoil, cause at this point i have no weapon detection . Always "none".
But probably because i don't have the right prerequisites ( like in game setting or something like that )
Or cause i'm using xbox stream app on a second monitor...
I tried to adjust the window in advance input settings but still haven't any detection.
I don't change default settings for brightness or anything but i usualy play with ALC so i have to try with 6/6 sens and "classic/small".
This will be the next step
In the meantime thank you very much for your help, it's very nice
Now i just need to understand all the information in the 35 pages of this topic [GCV/GPC] Apex Legends CV Anti-Recoil, cause at this point i have no weapon detection . Always "none".
But probably because i don't have the right prerequisites ( like in game setting or something like that )
Or cause i'm using xbox stream app on a second monitor...
I tried to adjust the window in advance input settings but still haven't any detection.
I don't change default settings for brightness or anything but i usualy play with ALC so i have to try with 6/6 sens and "classic/small".
This will be the next step
In the meantime thank you very much for your help, it's very nice
-
belpoutre - Staff Sergeant
- Posts: 11
- Joined: Mon Apr 23, 2018 3:25 pm
Re: GCV Error for a newbie on WIN 10
With the xbox app most of the time this issue is caused by a wrong offset of the monitor configuration:
It may be looking 2 pixels in the x and 1 in the y direction out of place:
viewtopic.php?f=15&t=15147&p=105420&hilit=offset#p105420
It may be looking 2 pixels in the x and 1 in the y direction out of place:
viewtopic.php?f=15&t=15147&p=105420&hilit=offset#p105420
-
Scachi - Brigadier General
- Posts: 3044
- Joined: Wed May 11, 2016 6:25 am
- Location: Germany
11 posts
• Page 1 of 2 • 1, 2
Return to Gtuner Computer Vision
Who is online
Users browsing this forum: No registered users and 68 guests