Page 9 of 12

Re: Titan Two Firmware 1.05-BETA (FEEDBACK NEEDED)

PostPosted: Sat Sep 14, 2019 11:35 am
by J2Kbr
Completing the packets synchronization update, the revision 6 of the 1.05 beta firmware adds the following:

* BT Stack: Synchronization of I/O packets transmission with the protocol maximum Bluetooth polling rate
* USB Host: Synchronization of I/O packets with the USB frame corresponding to the USB polling rate

With these changes is expected:

- led_set(), ffb_set() and related functions should not cause E4 (out-of-memory) error even if called on every iteration of main().
- Lower latency and better stability for Bluetooth connections (specially with consoles).
- Improvements of the Xbox Wireless Adapter support and wireless connection with XB1 controllers.

Re: Titan Two Firmware 1.05-BETA

PostPosted: Mon Sep 16, 2019 8:51 pm
by DontAtMe
I found an issue with the bluetooth connection.
When I connect my Xbox One controller via Bluetooth.

View (BUTTON_2) is not mapped to anything.
Menu (BUTTON_3) is not mapped to anything.
Right Bumper (BUTTON_4) is mapped to Menu (BUTTON_3)
Left Bumper (BUTTON_7) is mapped to View (BUTTON_2)
So pressing the bumpers results in Menu or View being outputted instead,
and pressing Menu or View results in no input/output.

Basically BUTTON_4 and BUTTON_7 cannot be outputted with a Xbox One controller when connected via bluetooth.
Does not matter what Output the Titan Two is set to.

This issue is only present using the bluetooth connection.
Connecting the controller using the Wireless Adapter or by USB to the Titan Two, work normally.

Re: Titan Two Firmware 1.05-BETA

PostPosted: Tue Sep 17, 2019 8:53 am
by J2Kbr
I have just tested a XB1 S controller here and the mapping is correct. Perhaps your controller is updated with a newer firmware version. I will try update mine and check again. thanks.

Re: Titan Two Firmware 1.05-BETA

PostPosted: Tue Sep 17, 2019 11:30 am
by DontAtMe
J2Kbr wrote:I have just tested a XB1 S controller here and the mapping is correct. Perhaps your controller is updated with a newer firmware version. I will try update mine and check again. thanks.

Thanks,

Also to add, a few more buttons are also effected.

X (BUTTON_17) is mapped to Y (BUTTON_13)
Y (BUTTON_13) is mapped to Right Bumper (BUTTON_4)
Right Stick (BUTTON_6) and Left Stick (BUTTON_9) are not mapped.

I have two Xbox One S controllers on hand, and both are updated to 4.8.1908.0.

Re: Titan Two Firmware 1.05-BETA

PostPosted: Tue Sep 17, 2019 1:31 pm
by bonefisher
I'm getting a orange flash on the output to console every now and then that shuts controller down. This is normal setup on xbox wired connections!

Re: Titan Two Firmware 1.05-BETA

PostPosted: Tue Sep 17, 2019 1:59 pm
by J2Kbr
Thanks DontAtMe.

I have just checked my Xbox One S controller and the firmware version is different from yours.
Xbox S Controller.png
Xbox S Controller.png (96.86 KiB) Viewed 1880 times

Strangely, it says there is no update available, even after trying update.

With this controller the button mappings are all correct.

Re: Titan Two Firmware 1.05-BETA

PostPosted: Tue Sep 17, 2019 2:00 pm
by J2Kbr
bonefisher wrote:I'm getting a orange flash on the output to console every now and then that shuts controller down. This is normal setup on xbox wired connections!

Do you have any script running? If yes, could you please check if the described issues also happens when using the device without any running script, thanks.

Re: Titan Two Firmware 1.05-BETA

PostPosted: Tue Sep 17, 2019 2:27 pm
by bonefisher
Ok no script running and took ffb off on all ports plus not doing anything and seen it flash orange split second like maybe xbox is checking or something!

Re: Titan Two Firmware 1.05-BETA

PostPosted: Tue Sep 17, 2019 2:30 pm
by bonefisher
Sitting watching it flash orange every 12 to 15 seconds not doing anything with no script!

Re: Titan Two Firmware 1.05-BETA

PostPosted: Tue Sep 17, 2019 2:40 pm
by bonefisher
I was checking the power source because that was flashing about the same time between port to console and prog port but was not that because plugged DC power jack in and now solid on power source. Still blinking on OUTPUT to console orange led flash every 12 to 15 seconds.