Titan Two Led flashing 3 & 4 with red lights fault?
12 posts
• Page 1 of 2 • 1, 2
Titan Two Led flashing 3 & 4 with red lights fault?
Hi there kind people, can anyone shed some light on my problem please.
Setup
Xbox one X > Titan Two > Xim 4
I've been using this setup for a while with no problems, however the USB cable that i connect the Titan Two to the xbox is a really cheap thing and is like 10 Inches long. I want it longer (about a meter) so i can rest the titan on my desk. I've tried about 5 different USB cables but every other cable gives me red flashing lights with the LED display flashing the number 3 and 4. Does anyone know what this is?
Throughout my set up none of my cables are over 1.5 meters.
Thanks in advance
Setup
Xbox one X > Titan Two > Xim 4
I've been using this setup for a while with no problems, however the USB cable that i connect the Titan Two to the xbox is a really cheap thing and is like 10 Inches long. I want it longer (about a meter) so i can rest the titan on my desk. I've tried about 5 different USB cables but every other cable gives me red flashing lights with the LED display flashing the number 3 and 4. Does anyone know what this is?
Throughout my set up none of my cables are over 1.5 meters.
Thanks in advance
-
ApexThor - Sergeant
- Posts: 7
- Joined: Mon Mar 25, 2019 9:54 am
Re: Titan Two Led flashing 3 & 4 with red lights fault?
Is it displaying E3/E4 or just 3/4 ?
Do you have a script loaded when this happens?
Do you have a script loaded when this happens?
ConsoleTuner Support Team || ConsoleTuner Discord || InputSense Discord
- Mad
- Major General
- Posts: 4536
- Joined: Wed May 22, 2019 5:39 am
Re: Titan Two Led flashing 3 & 4 with red lights fault?
Mad wrote:Is it displaying E3/E4 or just 3/4 ?
Do you have a script loaded when this happens?
Hi, thanks for your reply, just 3 / 4 no script loaded at this point. Just when i plug it into the Xbox
-
ApexThor - Sergeant
- Posts: 7
- Joined: Mon Mar 25, 2019 9:54 am
Re: Titan Two Led flashing 3 & 4 with red lights fault?
Are you sure it's not flashing AU?
If it's an error code it will be AU (controller not authenticating) or errors E1-4
Try without the xim and plug the controller directly into input A
If it's an error code it will be AU (controller not authenticating) or errors E1-4
Try without the xim and plug the controller directly into input A
ConsoleTuner Support Team || ConsoleTuner Discord || InputSense Discord
- Mad
- Major General
- Posts: 4536
- Joined: Wed May 22, 2019 5:39 am
Re: Titan Two Led flashing 3 & 4 with red lights fault?
E4 error means the RAM memory of the device is full, compromising regular operations such as USB communication. In this state the device must be reset, this can be done by power-off and then power-on, or by pressing both device's buttons.
This error can be caused by bad USB communication. Please try use a short cable to check if it solves the issue.
This error can be caused by bad USB communication. Please try use a short cable to check if it solves the issue.
ConsoleTuner Support Team
-
J2Kbr - General of the Army
- Posts: 20323
- Joined: Tue Mar 18, 2014 1:39 pm
Re: Titan Two Led flashing 3 & 4 with red lights fault?
J2Kbr wrote:E4 error means the RAM memory of the device is full, compromising regular operations such as USB communication. In this state the device must be reset, this can be done by power-off and then power-on, or by pressing both device's buttons.
This error can be caused by bad USB communication. Please try use a short cable to check if it solves the issue.
Hi thanks for the advice, sorry for the delay I've been away, I will double check the error code, it does work with a very short USB cable, but it won't work with anything else even USB cables that a 2 feet in length. I only have one script on the device, would this be linked to the RAM problem
regards
-
ApexThor - Sergeant
- Posts: 7
- Joined: Mon Mar 25, 2019 9:54 am
Re: Titan Two Led flashing 3 & 4 with red lights fault?
The USB cable must be able to transfer data, so not all cables will work.
It is possible it is the script, what one are you using? If open source post it here so we can take a look.
It is possible it is the script, what one are you using? If open source post it here so we can take a look.
ConsoleTuner Support Team || ConsoleTuner Discord || InputSense Discord
- Mad
- Major General
- Posts: 4536
- Joined: Wed May 22, 2019 5:39 am
Re: Titan Two Led flashing 3 & 4 with red lights fault?
It seems the long cable you are using is causing poor connection, resulting on E4 error.
A high quality cable should fix this issue.
A high quality cable should fix this issue.
ConsoleTuner Support Team
-
J2Kbr - General of the Army
- Posts: 20323
- Joined: Tue Mar 18, 2014 1:39 pm
Re: Titan Two Led flashing 3 & 4 with red lights fault?
J2Kbr wrote:It seems the long cable you are using is causing poor connection, resulting on E4 error.
A high quality cable should fix this issue.
Thanks for all the help, the code definitely just flashes 3 and 4 with all other lights solid red.
I tried just a slightly longer cable about 1 foot, and swapped my xbox controller cable to one that is 6" and this also worked, it's all very strange.
It's like there is not enough power but i'm using the smallest of cable runs
-
ApexThor - Sergeant
- Posts: 7
- Joined: Mon Mar 25, 2019 9:54 am
Re: Titan Two Led flashing 3 & 4 with red lights fault?
ApexThor wrote:It's like there is not enough power but i'm using the smallest of cable runs
Correct, long cables have higher voltage drop (especially if the power lines a not thicker), which can also be the cause for E4.
ConsoleTuner Support Team
-
J2Kbr - General of the Army
- Posts: 20323
- Joined: Tue Mar 18, 2014 1:39 pm
12 posts
• Page 1 of 2 • 1, 2
Who is online
Users browsing this forum: No registered users and 158 guests