[Question] XIM Disconnections within T2
Moderator: antithesis
6 posts
• Page 1 of 1
[Question] XIM Disconnections within T2
Hey there,
Tested Setups:
M/K/Controller -> Powered USB HUB ->XIM ->T2 -> Xbox = Xim gets shutdown/disconnected after 3-9 seconds. Replug = same after 3-9 seconds.
M/K/Controller -> NONpowerd USB HUB ->XIM ->T2 -> Xbox = Xim gets shutdown/disconnected after 3-9 seconds. Replug = same after 3-9 seconds.
M/K/Controller -> Nonpowered USB HUB ->XIM -> powered T2 -> Xbox = Xim gets shutdown/disconnected after 3-9 seconds. Replug = same after 3-9 seconds.
and other combinations...
Tested old firmware from 03.2020? and Beta.
Tested Controller: Xbox one 1708
Tested Mice: Zowie whatever, deathadder v1
Tested Keyboard: random cheap keyboard, random speedlink gaming keyboard
Xim Apex 1000hz
T2 Input polling default, output 1000Hz,Protocol: Auto & Xbox One.
Micro SD, formatted and configured..
Cables all funcional.
Somebody got a suggestion how to pair 'em, or is my T2 simply faulty?
Tested Setups:
M/K/Controller -> Powered USB HUB ->XIM ->T2 -> Xbox = Xim gets shutdown/disconnected after 3-9 seconds. Replug = same after 3-9 seconds.
M/K/Controller -> NONpowerd USB HUB ->XIM ->T2 -> Xbox = Xim gets shutdown/disconnected after 3-9 seconds. Replug = same after 3-9 seconds.
M/K/Controller -> Nonpowered USB HUB ->XIM -> powered T2 -> Xbox = Xim gets shutdown/disconnected after 3-9 seconds. Replug = same after 3-9 seconds.
and other combinations...
Tested old firmware from 03.2020? and Beta.
Tested Controller: Xbox one 1708
Tested Mice: Zowie whatever, deathadder v1
Tested Keyboard: random cheap keyboard, random speedlink gaming keyboard
Xim Apex 1000hz
T2 Input polling default, output 1000Hz,Protocol: Auto & Xbox One.
Micro SD, formatted and configured..
Cables all funcional.
Somebody got a suggestion how to pair 'em, or is my T2 simply faulty?
-
Lunara - Private First Class
- Posts: 3
- Joined: Wed Sep 23, 2020 4:43 pm
Re: [Question] XIM Disconnections within T2
Does the Titan Two work without out the Xim?
Please confirm this first. Before any other troubleshooting. After you have done that.
Try setting the Xim Apex Report rate to 125hz.
Also, set the output polling and input polling for the T2 to 125hz. Do not set it to the default protocol.
Please report back if the disconnections still happen after these steps, Thanks. .
Please confirm this first. Before any other troubleshooting. After you have done that.
Try setting the Xim Apex Report rate to 125hz.
Also, set the output polling and input polling for the T2 to 125hz. Do not set it to the default protocol.
Please report back if the disconnections still happen after these steps, Thanks. .
-
DontAtMe - Captain
- Posts: 502
- Joined: Tue Oct 02, 2018 4:49 am
Re: [Question] XIM Disconnections within T2
DontAtMe wrote:Does the Titan Two work without out the Xim?
Please confirm this first. Before any other troubleshooting. After you have done that.
Try setting the Xim Apex Report rate to 125hz.
Also, set the output polling and input polling for the T2 to 125hz. Do not set it to the default protocol.
Please report back if the disconnections still happen after these steps, Thanks. .
Heya,
Controller + (nonpowered) T2 -> Box works. But it delays sometimes like once in a minute for like 0.5 sec.
The thing with 125Hz was what I've done first, I just didn't write it down. I had 125Hz output/input on Titan Two aswell on XimA.125Hz as global setting.
An Example:
Titan Two to Box -> Output green.
Wait Auth.
Plug XIM etc.
Gets authenticated and works.
Input A Green.
3-10 sec later box says no controller connected.
Input A Red.
Controller turns off or Xim turns off an on again.
Input A Green again, but Controller is not responsive /not working.
(If I then replug XimA etc. it gets authenticated again [with luck] and the story starts again)
And so on, obviously LEDs behavior are different when I tried stuff in other directions and so on. ^^
-
Lunara - Private First Class
- Posts: 3
- Joined: Wed Sep 23, 2020 4:43 pm
Re: [Question] XIM Disconnections within T2
Thank you for checking,
What model is your Xbox One.
Orginal, S, X or All digital?
What model is your Xbox One.
Orginal, S, X or All digital?
-
DontAtMe - Captain
- Posts: 502
- Joined: Tue Oct 02, 2018 4:49 am
Re: [Question] XIM Disconnections within T2
DontAtMe wrote:Thank you for checking,
What model is your Xbox One.
Orginal, S, X or All digital?
Xbox One X
-
Lunara - Private First Class
- Posts: 3
- Joined: Wed Sep 23, 2020 4:43 pm
Re: [Question] XIM Disconnections within T2
Lunara wrote:DontAtMe wrote:Thank you for checking, What model is your Xbox One. Orginal, S, X or All digital?
Xbox One X
Please try use one of USB ports at the back of the Xbox One X to connect the Titan Two. Some users have already reported issues when using the front USB port of the console.
ConsoleTuner Support Team
-
J2Kbr - General of the Army
- Posts: 20323
- Joined: Tue Mar 18, 2014 1:39 pm
6 posts
• Page 1 of 1
Return to XIM Apex, XIM4, XIM Edge with Titan devices
Who is online
Users browsing this forum: No registered users and 34 guests