x1-t1-xim4 not working

[y2k]

so i decided to dust off my xbox one to play black ops 1 and got everything working (was able to change profile on t1)but my M&K will not responded ,the xim app show no bottom are being push,i try this with all my m&K on ps4 it work just fine.

-------------
setup

t1 connect to x1 wait for AU(pass)
connect controller to T1 (Pass)
quickly connect XIM4 to T1,profile load correct on t1(pass)
XIM4 App open and connect(pass)
M&K not responding(Fail)
t1 work fine with just controller

--------------
t1 setting

output-Automatic
Config-Slot recall
Speed up setting -Inframe out,1mss response
Rumble-DISABLE

[J2Kbr]

On the XIM, which controller you are using? Please note the Xbox One controller does not works, you need use any other controller, as explained in this topic, please check the xbox one part.

viewtopic.php?f=20&t=2252

[y2k]

On the XIM, which controller you are using? Please note the Xbox One controller does not works, you need use any other controller, as explained in this topic, please check the xbox one part.

viewtopic.php?f=20&t=2252

ya, that where i got the instruction from.for some reason my keyboard and mouse are not reponding

i use the ps4 controller on xim4 port

[J2Kbr]

Thanks for the information. At least you can operate the console using the controller?

[y2k]

Thanks for the information. At least you can operate the console using the controller?

the controller work while plug with xim

[J2Kbr]

Okay. As I have stated in the step-by-step guide, I haven't actually tested with the keyboard and mouse. however, we got confirmation of other users that it was working. I all try perform a more complete test on Xbox One and in the mean while try contact other users to get more details on their setups. Thanks.

[antithesis]

The XB1 controller does work with Titan One and Xim4.

I've been doing it since I bought the T1 and I've posted about this numerous times at the Xim forums - http://xim4.com/community/index.php?topic=43463.0

For those having problems with XB1 -

1. Turn on XB1.
2. Connect T1 to XB1.
3. Plug XB1 controller into T1.
4. Authenticate with XB1 controller. T1 will report 0.
5. Unplug XB1 controller from T1, plug controller into Xim4.
6. Plug Xim4 into XB1 - T1 will report AU, before changing to 0.
7. T1 + Xim4 + XB1 controller works.

I personally don't need to go to all that trouble. I simply leave the batteries out of the XB1 controller, plug it into the Xim4, plug that into the XB1, then turn the XB1 on. Done.

To troubleshoot - remove the XB1 controller battery and/or try a different USB cable to connect the XB1 controller to Xim. I use the same cable for PS4 and XB1.

If the XB1 console is already powered on when the Xim + T1 + XB1 controller are plugged in, the T1 sits on AU and the XB1 controller won't detect. How I get around this is to toggle between inputs on a USB switch, which is used to swap the Xim between consoles.

Powering down the XB1 completely, plugging in Xim + T1 + XB1 controller, then turning on the XB1 might be the simple solution folks are looking for.

[antithesis]

Does bbcode not work? Is there no Edit Post option?!?

[J2Kbr]

The bbcode is working ... please check in you user setting if you have it turned off by default.