Page 15 of 24

Cannot transfer bytecode from Gtuner Air

PostPosted: Fri Nov 01, 2019 11:10 pm
by hiraken
I connected Gtuner Air to Titan two for the first time.
Even if I select the saved GBC and tap “Load and run”, it does not move forward no matter how much time passes with “Storing Bytecode ...” displayed.
I tried several GBCs but all had the same symptoms.
I don't know what's wrong.
Is there a mistake in my usage?

Re: Gtuner Air: the smartphone/tablet App for the Titan Two

PostPosted: Sat Nov 02, 2019 2:13 am
by numberone
Need some help.

I've installed the bluetooth module, formatted/configured the SD card, but when I try to connect to the Titan Two via GTuner Air for iOS, it just spins on "Scanning for Titan Two device" and never connects. Is there something I'm doing wrong?

Re: Gtuner Air: the smartphone/tablet App for the Titan Two

PostPosted: Sat Nov 02, 2019 3:41 am
by numberone
numberone wrote:Need some help.

I've installed the bluetooth module, formatted/configured the SD card, but when I try to connect to the Titan Two via GTuner Air for iOS, it just spins on "Scanning for Titan Two device" and never connects. Is there something I'm doing wrong?


Hmm, I think the SD card is bad. Originally I was getting FS Error (2) but I removed the card, put it back in, formatted and ran the "Configure" option and it seemed like it completed successfully. The BT module was showing as loaded (at least from what I could tell). But I tried formatting the SD card again and it just keeps failing. Tried to format it on macOS as FAT and that failed too. Going to go out to BBY and buy a new microSD card and see if that works.

Re: Gtuner Air: the smartphone/tablet App for the Titan Two

PostPosted: Sat Nov 02, 2019 8:52 pm
by numberone
numberone wrote:
numberone wrote:Need some help.

I've installed the bluetooth module, formatted/configured the SD card, but when I try to connect to the Titan Two via GTuner Air for iOS, it just spins on "Scanning for Titan Two device" and never connects. Is there something I'm doing wrong?


Hmm, I think the SD card is bad. Originally I was getting FS Error (2) but I removed the card, put it back in, formatted and ran the "Configure" option and it seemed like it completed successfully. The BT module was showing as loaded (at least from what I could tell). But I tried formatting the SD card again and it just keeps failing. Tried to format it on macOS as FAT and that failed too. Going to go out to BBY and buy a new microSD card and see if that works.


Turns out the microSD card was bad. Bought a 32 GB one from BBY, formatted it, configured it, now the BT module is working fine.

Re: Gtuner Air: the smartphone/tablet App for the Titan Two

PostPosted: Sat Nov 02, 2019 10:12 pm
by Mad
numberone wrote:Turns out the microSD card was bad. Bought a 32 GB one from BBY, formatted it, configured it, now the BT module is working fine.


Glad to hear it's working :smile0517:

Re: Gtuner Air: the smartphone/tablet App for the Titan Two

PostPosted: Sun Nov 03, 2019 3:55 am
by numberone
Mad wrote:
numberone wrote:Turns out the microSD card was bad. Bought a 32 GB one from BBY, formatted it, configured it, now the BT module is working fine.


Glad to hear it's working :smile0517:


Thanks. I should also add that Gtuner IV crashes quite frequently on macOS Catalina, but then again Catalina has not been great so far for other things. Think I'm going to downgrade back to Mojave.

Re: Cannot transfer bytecode from Gtuner Air

PostPosted: Mon Nov 04, 2019 7:04 am
by J2Kbr
hiraken wrote:I connected Gtuner Air to Titan two for the first time. Even if I select the saved GBC and tap “Load and run”, it does not move forward no matter how much time passes with “Storing Bytecode ...” displayed. I tried several GBCs but all had the same symptoms. I don't know what's wrong.

It seems there is some sort communication issue between Gtuner Air and the Titan Two.
hiraken wrote:Is there a mistake in my usage?

Are you on iOS or Android?

Re: Cannot transfer bytecode from Gtuner Air

PostPosted: Mon Nov 04, 2019 4:06 pm
by hiraken
J2Kbr wrote:
hiraken wrote:I connected Gtuner Air to Titan two for the first time. Even if I select the saved GBC and tap “Load and run”, it does not move forward no matter how much time passes with “Storing Bytecode ...” displayed. I tried several GBCs but all had the same symptoms. I don't know what's wrong.

It seems there is some sort communication issue between Gtuner Air and the Titan Two.
hiraken wrote:Is there a mistake in my usage?

Are you on iOS or Android?


I am using Android.
Changes to Connect and Output Protocol can be made normally.

Re: Gtuner Air: the smartphone/tablet App for the Titan Two

PostPosted: Wed Nov 13, 2019 8:02 am
by J2Kbr
Thank you for confirming your are using with Android.

I just tested with an Android phone and it worked as expected. Could you please inform what is the Android version you have installed in your device? Thank you.

Re: Gtuner Air: the smartphone/tablet App for the Titan Two

PostPosted: Mon Nov 18, 2019 11:31 am
by Marcin
Hello. Can I connect Gtuner Air Android OS via OTG cable to my phone?