Titan Two just turned off after FW Update
7 posts
• Page 1 of 1
Titan Two just turned off after FW Update
Have my T2 now a few month and all worked fine till today.
Got a Message in GTuner to update to the newest FW.
After i did that, my Titan Two just powered off and i cant get it powered on anymore. It keeps disconnected.
Got a Message in GTuner to update to the newest FW.
After i did that, my Titan Two just powered off and i cant get it powered on anymore. It keeps disconnected.
-
ShimmiShu - Sergeant Major
- Posts: 73
- Joined: Tue Mar 17, 2020 11:30 am
Re: Titan Two just turned off after FW Update
ShimmiShu wrote:Have my T2 now a few month and all worked fine till today.
Got a Message in GTuner to update to the newest FW.
After i did that, my Titan Two just powered off and i cant get it powered on anymore. It keeps disconnected.
Hi, Please try a different USB cable.
ConsoleTuner Support Team || ConsoleTuner Discord || InputSense Discord
- Mad
- Major General
- Posts: 4536
- Joined: Wed May 22, 2019 5:39 am
Re: Titan Two just turned off after FW Update
Please try reflash the Titan Two firmware. For that, before connect the Titan Two to the computer via the PROG port, press and hold both buttons and only then connect it to your computer. The device should enter in programming mode, showing P on the display, allowing redo the firmware update using Gtuner IV (Tools -> Check for Updates).
ConsoleTuner Support Team
-
J2Kbr - General of the Army
- Posts: 20323
- Joined: Tue Mar 18, 2014 1:39 pm
Re: Titan Two just turned off after FW Update
@J2Kbr i cant bring into prog mode because its just not getting power anymore.
@Mad I did already. Also different USB Ports on Console and PC. Nothing worked. T2 is just "dead" after the newest Update.
@Mad I did already. Also different USB Ports on Console and PC. Nothing worked. T2 is just "dead" after the newest Update.
-
ShimmiShu - Sergeant Major
- Posts: 73
- Joined: Tue Mar 17, 2020 11:30 am
Re: Titan Two just turned off after FW Update
ShimmiShu wrote:@J2Kbr i cant bring into prog mode because its just not getting power anymore.
If the updated fails to complete (e.g. due unplugging the USB cable while performing the update), the device will not turn on its numeric display or LEDs.
However, it should still be possible force the device to enter in programming mode (when P is shown in its display) by pressing and holding both buttons BEFORE plug the USB cable to the PROG port (the other end of this cable should already be connected to your computer).
ConsoleTuner Support Team
-
J2Kbr - General of the Army
- Posts: 20323
- Joined: Tue Mar 18, 2014 1:39 pm
Re: Titan Two just turned off after FW Update
Ohhh for f** sake.... This damn cables i was using, 3 in row, are all broke too... Works now..
Gosh exuse my behave..... i cant say sorry enough.
Thank u so much...
Gosh exuse my behave..... i cant say sorry enough.
Thank u so much...
-
ShimmiShu - Sergeant Major
- Posts: 73
- Joined: Tue Mar 17, 2020 11:30 am
Re: Titan Two just turned off after FW Update
No problem thank you for the update.
ConsoleTuner Support Team || ConsoleTuner Discord || InputSense Discord
- Mad
- Major General
- Posts: 4536
- Joined: Wed May 22, 2019 5:39 am
7 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 73 guests