Firmware Update "broke" my T2
25 posts
• Page 1 of 3 • 1, 2, 3
Firmware Update "broke" my T2
Fellow Titaneers!
As the title says, my beloved T2 is having an issue since I installed the most recent Firmware.
After every FW Update i have to re-pair my DS4 Controller with the Titan 2. No Problem so far. After turning off my PS4 and turning it on again, my T2 says "AU" and I turn on the Controller. This is where the Problem happens with the new FW.
The Controller turns ON and the LED turns Solid Blue and suggests that everything is fine but the Titan keep flashing "AU". They just wont connect. What I do then is: I turn off the Controller and then i put both the Controller and the Titan in pairing mode so they find each other and eventually connect. I need to do this every time, when I turn off the PS4 (same for standby). Doing this every time when i want to play is pretty annoying and is not what I'm used to since this problem never happened before.
Any suggestions what i could do about this? Replugging all cables didnt help, I also removed the BT Chip and reinserted it which didnt help.
As the title says, my beloved T2 is having an issue since I installed the most recent Firmware.
After every FW Update i have to re-pair my DS4 Controller with the Titan 2. No Problem so far. After turning off my PS4 and turning it on again, my T2 says "AU" and I turn on the Controller. This is where the Problem happens with the new FW.
The Controller turns ON and the LED turns Solid Blue and suggests that everything is fine but the Titan keep flashing "AU". They just wont connect. What I do then is: I turn off the Controller and then i put both the Controller and the Titan in pairing mode so they find each other and eventually connect. I need to do this every time, when I turn off the PS4 (same for standby). Doing this every time when i want to play is pretty annoying and is not what I'm used to since this problem never happened before.
Any suggestions what i could do about this? Replugging all cables didnt help, I also removed the BT Chip and reinserted it which didnt help.
-
CrophiXx - Sergeant
- Posts: 7
- Joined: Thu Jul 26, 2018 1:39 am
Re: Firmware Update "broke" my T2
I had the same issue.
Hit the "Configure" button for the SD-card again and restart the T2.
If someone has problems finding the button, from the expansion kit doc page:
https://www.consoletuner.com/wiki/index ... figuration
Open Gtuner IV and go to the panel named Device Configuration.
Locate the sub-section Micro-SD Card and click on the button Configure.
It is stated in the update change log, easy to miss as I don't think everyone is reading those:
https://www.consoletuner.com/titan-two-downloads/
The changelog is also accessible via Gtuner iV->Help->About GTuner->[View Changelog] Button (opens in your browser).
Always hitting the Configure button after a Firmware update is what I will do from now on
Hit the "Configure" button for the SD-card again and restart the T2.
If someone has problems finding the button, from the expansion kit doc page:
https://www.consoletuner.com/wiki/index ... figuration
Open Gtuner IV and go to the panel named Device Configuration.
Locate the sub-section Micro-SD Card and click on the button Configure.
It is stated in the update change log, easy to miss as I don't think everyone is reading those:
https://www.consoletuner.com/titan-two-downloads/
The changelog is also accessible via Gtuner iV->Help->About GTuner->[View Changelog] Button (opens in your browser).
Always hitting the Configure button after a Firmware update is what I will do from now on
-
Scachi - Brigadier General
- Posts: 3044
- Joined: Wed May 11, 2016 6:25 am
- Location: Germany
Re: Firmware Update "broke" my T2
I have the same issue since latest firmware version - using Xbox One X and DS4 controller with T2 + Bluetooth module.
I will try Scachi's instructions and post back on resolution. Thanks.
I'm hoping this bug is fixed though and that this isn't required. I liked not having to do any additional steps after updating firmware..
I will try Scachi's instructions and post back on resolution. Thanks.
Always hitting the Configure button after a Firmware update is what I will do from now on
I'm hoping this bug is fixed though and that this isn't required. I liked not having to do any additional steps after updating firmware..
- velocd
- Staff Sergeant
- Posts: 13
- Joined: Wed May 03, 2017 6:16 pm
Re: Firmware Update "broke" my T2
Scachi wrote:I had the same issue.
Hit the "Configure" button for the SD-card again and restart the T2.
If someone has problems finding the button, from the expansion kit doc page:
https://www.consoletuner.com/wiki/index ... figuration
Open Gtuner IV and go to the panel named Device Configuration.
Locate the sub-section Micro-SD Card and click on the button Configure.
It is stated in the update change log, easy to miss as I don't think everyone is reading those:
https://www.consoletuner.com/titan-two-downloads/
The changelog is also accessible via Gtuner iV->Help->About GTuner->[View Changelog] Button (opens in your browser).
Always hitting the Configure button after a Firmware update is what I will do from now on
Thank you, Sir! One press on "Configure" and my problem was solved!
I have to admit, that I don't always read the changelog :D
-
CrophiXx - Sergeant
- Posts: 7
- Joined: Thu Jul 26, 2018 1:39 am
Re: Firmware Update "broke" my T2
Just replying that Scachi's instructions fixed my issue too. Thanks!
- velocd
- Staff Sergeant
- Posts: 13
- Joined: Wed May 03, 2017 6:16 pm
Re: Firmware Update "broke" my T2
I am considering include "auto Configure" as a process of the software/firmware update. Something like: if the Titan Two has SD-Card and the update detected any file in the configsd folder changed -> do "Configure" automatically.
ConsoleTuner Support Team
-
J2Kbr - General of the Army
- Posts: 20323
- Joined: Tue Mar 18, 2014 1:39 pm
Re: Firmware Update "broke" my T2
J2Kbr wrote:I am considering include "auto Configure" as a process of the software/firmware update. Something like: if the Titan Two has SD-Card and the update detected any file in the configsd folder changed -> do "Configure" automatically.
Sounds like a good idea!
-
CrophiXx - Sergeant
- Posts: 7
- Joined: Thu Jul 26, 2018 1:39 am
Re: Firmware Update "broke" my T2
I'm having this issue as well, however, I do not have an SD card and the option to configure is greyed out. Please help.
-
QZ900 - Sergeant
- Posts: 9
- Joined: Thu Nov 22, 2018 4:57 am
Re: Firmware Update "broke" my T2
Welcome to our forums.
When using the controller wired to the Titan Two there is no needed of configure the SD-Card.
When using the controller wired to the Titan Two there is no needed of configure the SD-Card.
ConsoleTuner Support Team
-
J2Kbr - General of the Army
- Posts: 20323
- Joined: Tue Mar 18, 2014 1:39 pm
Re: Firmware Update "broke" my T2
Thank you.
My T2 was working fine before the update on 3/13. I've tried resetting and updating the firmware, removing and reinstalling the scripts, but anytime I plug it into my XB1X, I get the AU error. Any suggestions?
My T2 was working fine before the update on 3/13. I've tried resetting and updating the firmware, removing and reinstalling the scripts, but anytime I plug it into my XB1X, I get the AU error. Any suggestions?
-
QZ900 - Sergeant
- Posts: 9
- Joined: Thu Nov 22, 2018 4:57 am
25 posts
• Page 1 of 3 • 1, 2, 3
Who is online
Users browsing this forum: No registered users and 104 guests