Custom rack for the T2

Titan Two general support. Questions, firmware update, feature request.

Re: Custom rack for the T2

Postby jelly44 » Sat May 04, 2019 2:20 pm

Scachi wrote:
jelly44 wrote:Hi Scachi - not only did I buy the wrong 90 USB parts but my rack wasn't properly printed. Either the red part was too big or the green part was too small. So the parts don't fit.

Would you be able to send me the measurements of the red part, for the parts where the green part would fit? So that thin tower and the squared looking base?

Thanks a lot

The lower part is 7mm, the upper vertical stabilization triangle like part is 2mm wide.
The parts are a tight fit, it depends a bit on the printer if the resulted parts will fit easily.
You should be able to cut the opening of the green part a bit easily with a sharp knife like a cutter-knife or scalpel like knife.

I will adjust the green part a bit so the next person printing it will have no problems.

What are the dimensions of your usb adapters ? Or what is wrong with them so I can add more information to the first post.


The knife help. Nothing like some brute force!

The issue with the USB parts was that I'd have to use the T2 facing backwards. It's the USB up/down thing. The plastic piece in the USB part which plugs to the T2 needs to be up (I think).
- My recommendation for learning C programming: 'C Programming Absolute Beginner's Guide'
- Create your own scripts with GPC2 Scripting
User avatar
jelly44
Sergeant Major of the Army
Sergeant Major of the Army
 
Posts: 220
Joined: Tue Feb 05, 2019 3:49 pm

Re: Custom rack for the T2

Postby Scachi » Sat May 04, 2019 2:47 pm

jelly44 wrote:
Scachi wrote:What are the dimensions of your usb adapters ? Or what is wrong with them so I can add more information to the first post.

....
The issue with the USB parts was that I'd have to use the T2 facing backwards. It's the USB up/down thing. The plastic piece in the USB part which plugs to the T2 needs to be up (I think).

Oh, I am sorry for all the trouble. I have added this important information to the post.
User avatar
Scachi
Brigadier General
Brigadier General
 
Posts: 3044
Joined: Wed May 11, 2016 6:25 am
Location: Germany

Re: Custom rack for the T2

Postby jelly44 » Sat May 04, 2019 4:15 pm

it wasn't your fault. I trusted the picture on amazon, but I got a different one ;)
- My recommendation for learning C programming: 'C Programming Absolute Beginner's Guide'
- Create your own scripts with GPC2 Scripting
User avatar
jelly44
Sergeant Major of the Army
Sergeant Major of the Army
 
Posts: 220
Joined: Tue Feb 05, 2019 3:49 pm

Re: Custom rack for the T2

Postby B3YOND » Mon Nov 30, 2020 5:30 am

WHERE CAN I BUY ONE OF THESE STANDS FOR THE T2
User avatar
B3YOND
Private
Private
 
Posts: 1
Joined: Mon Nov 30, 2020 5:01 am

Re: Custom rack for the T2

Postby BEAST07 » Mon Nov 30, 2020 11:41 am

Great work Scachi,
I'm going to turn both adapters around and seat the titan on top of the monitor, with cables running behind the monitor to my pc. I was looking for led extension but know i don't need one.
User avatar
BEAST07
Sergeant Major
Sergeant Major
 
Posts: 74
Joined: Tue Jan 07, 2020 9:19 am

Re: Custom rack for the T2

Postby Scachi » Sun Jan 24, 2021 12:35 am

I have updated the design a bit. All files available via thingiverse https://www.thingiverse.com/thing:2722858
For more information about this rack read the first post: viewtopic.php?f=27&t=5388#p40355
User avatar
Scachi
Brigadier General
Brigadier General
 
Posts: 3044
Joined: Wed May 11, 2016 6:25 am
Location: Germany

Previous

Return to Titan Two Device

Who is online

Users browsing this forum: No registered users and 63 guests