Custom rack for the T2
26 posts
• Page 3 of 3 • 1, 2, 3
Re: Custom rack for the T2
Scachi wrote:jelly44 wrote:Hi Scachi - not only did I buy the wrong 90 USB parts but my rack wasn't properly printed. Either the red part was too big or the green part was too small. So the parts don't fit.
Would you be able to send me the measurements of the red part, for the parts where the green part would fit? So that thin tower and the squared looking base?
Thanks a lot
The lower part is 7mm, the upper vertical stabilization triangle like part is 2mm wide.
The parts are a tight fit, it depends a bit on the printer if the resulted parts will fit easily.
You should be able to cut the opening of the green part a bit easily with a sharp knife like a cutter-knife or scalpel like knife.
I will adjust the green part a bit so the next person printing it will have no problems.
What are the dimensions of your usb adapters ? Or what is wrong with them so I can add more information to the first post.
The knife help. Nothing like some brute force!
The issue with the USB parts was that I'd have to use the T2 facing backwards. It's the USB up/down thing. The plastic piece in the USB part which plugs to the T2 needs to be up (I think).
- My recommendation for learning C programming: 'C Programming Absolute Beginner's Guide'
- Create your own scripts with GPC2 Scripting
- Create your own scripts with GPC2 Scripting
-
jelly44 - Sergeant Major of the Army
- Posts: 220
- Joined: Tue Feb 05, 2019 3:49 pm
Re: Custom rack for the T2
jelly44 wrote:Scachi wrote:What are the dimensions of your usb adapters ? Or what is wrong with them so I can add more information to the first post.
....
The issue with the USB parts was that I'd have to use the T2 facing backwards. It's the USB up/down thing. The plastic piece in the USB part which plugs to the T2 needs to be up (I think).
Oh, I am sorry for all the trouble. I have added this important information to the post.
-
Scachi - Brigadier General
- Posts: 3044
- Joined: Wed May 11, 2016 6:25 am
- Location: Germany
Re: Custom rack for the T2
it wasn't your fault. I trusted the picture on amazon, but I got a different one ;)
- My recommendation for learning C programming: 'C Programming Absolute Beginner's Guide'
- Create your own scripts with GPC2 Scripting
- Create your own scripts with GPC2 Scripting
-
jelly44 - Sergeant Major of the Army
- Posts: 220
- Joined: Tue Feb 05, 2019 3:49 pm
Re: Custom rack for the T2
WHERE CAN I BUY ONE OF THESE STANDS FOR THE T2
-
B3YOND - Private
- Posts: 1
- Joined: Mon Nov 30, 2020 5:01 am
Re: Custom rack for the T2
Great work Scachi,
I'm going to turn both adapters around and seat the titan on top of the monitor, with cables running behind the monitor to my pc. I was looking for led extension but know i don't need one.
I'm going to turn both adapters around and seat the titan on top of the monitor, with cables running behind the monitor to my pc. I was looking for led extension but know i don't need one.
-
BEAST07 - Sergeant Major
- Posts: 74
- Joined: Tue Jan 07, 2020 9:19 am
Re: Custom rack for the T2
I have updated the design a bit. All files available via thingiverse https://www.thingiverse.com/thing:2722858
For more information about this rack read the first post: viewtopic.php?f=27&t=5388#p40355
For more information about this rack read the first post: viewtopic.php?f=27&t=5388#p40355
-
Scachi - Brigadier General
- Posts: 3044
- Joined: Wed May 11, 2016 6:25 am
- Location: Germany
26 posts
• Page 3 of 3 • 1, 2, 3
Who is online
Users browsing this forum: fox5 and 118 guests