help with bluettooth
41 posts
• Page 2 of 5 • 1, 2, 3, 4, 5
Re: help with bluettooth
J2Kbr wrote:go to the “Device Configuration” panel and check the “Bluetooth Module” status, if it show “HCI H4 (4Mbps)” means the module was successfully initialized and it is operational.
I have received the BT modules for my Titans but i have an issue. The first module i plugged in both Titans said "FW not found", next i plugged the second module and it said “HCI H4 (4Mbps)” but after unpluged and repluged it says now Initializing. Now both modules are in an endless initializing.
Console tuner since my 1st controller.
Scripting, a game in the game.
Believe or dare, It's Titanic!
Scripting, a game in the game.
Believe or dare, It's Titanic!
-
Prototype - Major General
- Posts: 3252
- Joined: Sun Dec 16, 2012 1:43 pm
Re: help with bluettooth
I think there is an issue with the module.
edit:all is working fine now
edit:all is working fine now
Last edited by paname on Wed Jan 17, 2018 11:08 pm, edited 2 times in total.
-
paname - Sergeant Major of the Army
- Posts: 204
- Joined: Wed Jan 07, 2015 3:02 pm
Re: help with bluettooth
prototype wrote:J2Kbr wrote:go to the “Device Configuration” panel and check the “Bluetooth Module” status, if it show “HCI H4 (4Mbps)” means the module was successfully initialized and it is operational.
I have received the BT modules for my Titans but i have an issue. The first module i plugged in both Titans said "FW not found", next i plugged the second module and it said “HCI H4 (4Mbps)” but after unpluged and repluged it says now Initializing. Now both modules are in an endless initializing.
I had to click on configuration again then it came back up!
- bonefisher
- Lieutenant General
- Posts: 5413
- Joined: Thu Jan 29, 2015 10:49 am
Re: help with bluettooth
Yes i did to load the BT FW but with no change.
Console tuner since my 1st controller.
Scripting, a game in the game.
Believe or dare, It's Titanic!
Scripting, a game in the game.
Believe or dare, It's Titanic!
-
Prototype - Major General
- Posts: 3252
- Joined: Sun Dec 16, 2012 1:43 pm
Re: help with bluettooth
The Module from production batch is a new revision (B1-Rev2), the one used for development was a prototype (B1-Rev1). I was not expecting, but the hardware changes required firmware changes as well.
I received 2 pcs from production batch yesterday and after a debugging session, fix and improvements...
...a new firmware release is now available.
Everything should work as expected now.
Apologize me for any inconvenience this may have caused.
--
Quick tip to pair PS4 controllers with the Titan Two.
There is two ways to perform this step:
1) Just connect the PS4 controller to the Titan Two with the cable, wait the blue light, unplug the controller. From here you should be able to press the PS button on the controller to start the wireless connection;
2) O Gtuner IV press the button “Pair Controller Wirelessly”. And, within 20 seconds, press and hold the SHARE and PS buttons on the controller until it start blinking white. After couple seconds the controller should turn BLUE, meaning it is paired and connected.
Please let me know your results.
I received 2 pcs from production batch yesterday and after a debugging session, fix and improvements...
...a new firmware release is now available.
Everything should work as expected now.
Apologize me for any inconvenience this may have caused.
--
Quick tip to pair PS4 controllers with the Titan Two.
There is two ways to perform this step:
1) Just connect the PS4 controller to the Titan Two with the cable, wait the blue light, unplug the controller. From here you should be able to press the PS button on the controller to start the wireless connection;
2) O Gtuner IV press the button “Pair Controller Wirelessly”. And, within 20 seconds, press and hold the SHARE and PS buttons on the controller until it start blinking white. After couple seconds the controller should turn BLUE, meaning it is paired and connected.
Please let me know your results.
ConsoleTuner Support Team
-
J2Kbr - General of the Army
- Posts: 20323
- Joined: Tue Mar 18, 2014 1:39 pm
Re: help with bluettooth
hi, all working now, ive only tested it to see if would connect and do 2 minutes on the ps4 but will properly test it later tonight but its definately working, thanks
-
Mark10 - Sergeant First Class
- Posts: 20
- Joined: Wed Mar 01, 2017 2:57 pm
Re: help with bluettooth
Awesome
The first way worked at the first try with a really quick pairing of the DS4!
Now let's connect to the PS4
The first way worked at the first try with a really quick pairing of the DS4!
Now let's connect to the PS4
Console tuner since my 1st controller.
Scripting, a game in the game.
Believe or dare, It's Titanic!
Scripting, a game in the game.
Believe or dare, It's Titanic!
-
Prototype - Major General
- Posts: 3252
- Joined: Sun Dec 16, 2012 1:43 pm
Re: help with bluettooth
Works awesome! Will it pair up to console? lol!
- bonefisher
- Lieutenant General
- Posts: 5413
- Joined: Thu Jan 29, 2015 10:49 am
Re: help with bluettooth
awesome, thank you guy for confirming the Bluetooth Module is working good now.
Connection with PS3 consoles is already implemented and can be used, more info here:
https://www.consoletuner.com/wiki/index ... connection
I will be working for PS4, Switch, Wii and Wii U pretty soon.
bonefisher wrote:Will it pair up to console? lol!
Connection with PS3 consoles is already implemented and can be used, more info here:
https://www.consoletuner.com/wiki/index ... connection
I will be working for PS4, Switch, Wii and Wii U pretty soon.
ConsoleTuner Support Team
-
J2Kbr - General of the Army
- Posts: 20323
- Joined: Tue Mar 18, 2014 1:39 pm
41 posts
• Page 2 of 5 • 1, 2, 3, 4, 5
Who is online
Users browsing this forum: Google [Bot], monteruntheplay and 114 guests