Logitech G110 w/ headset + KM Capture (Xbox1)

[Sliksta]

Just bought the Titan 2 and having an issue with getting it to detect/init the Logitech G110 keyboard when plugged in directly. It works via the KM capture feature, but because i use a wired headset/mic through the xbox controller every few minutes it disconnects and cuts out my headset mic or mic & audio. After a few times the connection ceases to work and i have to reboot the xbox for it to detect the controller, either through titan 2 or through the xbox directly.

When i use the setup without a headset plugged into the controller, it works without issue.

I've tried using an OTG cable for my keyboard and it doesnt work. Is there something i can do to get it to work with the G110?
I have not tried the Microsd card trick as with the g13.

Thank you!

[J2Kbr]

Please capture and send me the USB descriptors of your Logitech G110. On Gtuner IV, with the Titan Two connected to computer, go to top menu Tools -> "Fetch Descriptors ...". Now plug the G110 to any port on the Titan Two. The descriptors will show in the window, click on the button "Copy Descriptors" and post here. Thank you.

[Sliksta]

[USB DESCRIPTOR]
12 01 00 02 09 00 02 40 E3 05 07 06 01 08 00 01 00 01 09 02 29 00 01 01 00 E0 FA 09 04 00 00 01 09 00 01 00 07 05 81 03 01 00 0C 09 04 00 01 01 09 00 02 00 07 05 81 03 01 00 0C

[STRING 1 DESCRIPTOR]
00 00 00 02 00 00 02 01 80 06 03 01 04 09 00 16
16 03 55 00 53 00 42 00 32 00 2E 00 30 00 20 00 48 00 75 00 62 00

[J2Kbr]

Thank you, here is the descriptors decoded:

Code: Select all

[USB DESCRIPTOR]
12           bLength: 18
01           bDescriptorType: 1 - DEVICE
00 02        bcdUSB: 2.00
09           bDeviceClass: 9 (09)
00           bDeviceSubClass: 0 (00)
02           bDeviceProtocol: 2 (02)
40           bMaxPacketSize0: 64
E3 05        idVendor: 05E3
07 06        idProduct: 0607
01 08        bcdDevice: 8.01
00           iManufacturer: 0
01           iProduct: 1
00           iSerialNumber: 0
01           bNumConfigurations: 1

09           bLength: 9
02           bDescriptorType: 2 - CONFIGURATION
29 00        wTotalLength: 41
01           bNumInterfaces: 1
01           bConfigurationValue: 1
00           iConfiguration: 0
E0           bmAttributes: 224 (Self Powered, Remote Wakeup)
FA           MaxPower: 500mA

09             bLength: 9
04             bDescriptorType: 4 - INTERFACE
00             bInterfaceNumber: 0
00             bAlternateSetting: 0
01             bNumEndpoints: 1
09             bInterfaceClass: 9 (09)
00             bInterfaceSubClass: 0 (00)
01             bInterfaceProtocol: 1 (01)
00             iInterface: 0

07               bLength: 7
05               bDescriptorType: 5 - ENDPOINT
81               bEndpointAddress: 1 IN
03               bmAttributes: 3 (Interrupt, None, Data)
01 00            wMaxPacketSize: 1
0C               bInterval: 12

09             bLength: 9
04             bDescriptorType: 4 - INTERFACE
00             bInterfaceNumber: 0
01             bAlternateSetting: 1
01             bNumEndpoints: 1
09             bInterfaceClass: 9 (09)
00             bInterfaceSubClass: 0 (00)
02             bInterfaceProtocol: 2 (02)
00             iInterface: 0

07               bLength: 7
05               bDescriptorType: 5 - ENDPOINT
81               bEndpointAddress: 1 IN
03               bmAttributes: 3 (Interrupt, None, Data)
01 00            wMaxPacketSize: 1
0C               bInterval: 12

[STRING 1 DESCRIPTOR]
USB2.0 Hub


The issue this keyboard implements an USB Hub (as you can verify above). USB Hub is not currently supported by the Titan Two.

[Sliksta]

Thank you for your time. Excuse my ignorance,I don't understand what im suppose to do with the USB descriptor information? Also is the integrated usb hub what's causing my headset/mic to disconnect when using KM capture? When the headset is not plugged in, my keyboard and mouse work fine through KM capture.

I don't want to waste your valuable time, just need to know if i can make this work, or should i get a different KB? Or Would using my headset on a second controller work?

Thank you again for your time and hard work!

[J2Kbr]

Also is the integrated usb hub what's causing my headset/mic to disconnect when using KM capture? When the headset is not plugged in, my keyboard and mouse work fine through KM capture.

With the keyboard plugged on PC, the integrated usb hub is handled by the computer and is not the cause of disconnections with the headset connected to the controller.

I don't want to waste your valuable time, just need to know if i can make this work, or should i get a different KB? Or Would using my headset on a second controller work?

Please let me know what XB1 controller model you have (original, S or Elite). I will test the same devices/connections as you to try reproduce the disconnection issue. Recapping:

1) Titan Two on XB1;
2) XB1 controller with headset connected on INPUT-B of the Titan Two;
3) Gtuner IV with KM Capture active;

After have all this connected, how long is expected the disconnection to happen?

[Sliksta]

Thank you for looking so deep into this. I actually was able to do a workaround with a 2nd controller, however to answer your questions.

Please let me know what XB1 controller model you have (original, S or Elite). I will test the same devices/connections as you to try reproduce the disconnection issue. Recapping:

1) Titan Two on XB1;
2) XB1 controller with headset connected on INPUT-B of the Titan Two;
3) Gtuner IV with KM Capture active;

After have all this connected, how long is expected the disconnection to happen?

1) Titan 2 connected to XB1S via PROG port;
1.1) Titan 2 connected to PC via OUTPUT port
2) Genuine XB1S wireless controller via INPUT-A or B;
3) Gtuner IV with KM Capture active.
4) Kingston Hyper X Cloud Stinger connected to wireless controller via 3.5mm jack.
5) With and without 7.5V 2A power adapter.

Time till disconnect/reset: 3-7 mins, possibly as long as 10 mins. but no longer. After several times of reconnect/disconnect, controller will stop responding and XB will require a hardboot.

[J2Kbr]

Thank you.

[Sliksta]

tried the latest update feb-20, it helped with the disconnect, but not fully. Now what happens is mic will disconnect, but no longer locks up the controller. I didnt try anything else or any further testing since everything is working great using headset plugged into 2nd controller.

Also mouse x/y input seems a little bit smoother.

[J2Kbr]

thank you for the update. I am currently debugging/fixing issues related with controller headsets where, under some circumstances, causes the problems you are describing. Hopefully yet this week we will get this solved.