Titan two KM capture into Xim4
22 posts
• Page 1 of 3 • 1, 2, 3
Titan two KM capture into Xim4
is it possible to run the titan two into the xim4 and than use KM Capture as my mouse and keyboard so i can use my pc mouse and keyboard to use on xim4? and if it is possible how would i set this up?
-
fdg0d - Sergeant Major
- Posts: 83
- Joined: Thu May 12, 2016 3:16 pm
Re: Titan two KM capture into Xim4
fdg0d wrote:is it possible to run the titan two into the xim4 and than use KM Capture as my mouse and keyboard so i can use my pc mouse and keyboard to use on xim4? and if it is possible how would i set this up?
Yes it is possible.
Connect the t2 output into port 1 on the Xim 4. (where you use to plug your mouse in before).
A controller has to be connected to the Xim 4 for authentication. as well by the way.
Now select the correct output protocol within Gtuner IV's Device Configuration Window.
Also keep note that disable joystick should remain checked, If its not checked you will have issues.
Almost done.
Run this script on the T2.
- Code: Select all
init {
mousemapping();
}
main {
mouse_passthru();
key_passthru();
}
KM Capture.Is located under tools in the menu bar, alternatively the hot key f4, will also launch KM Capture.
Just make sure that script is running before you enter KM Capture, as this script will allow the passt-thru for both mouse and keyboard..
-
Sillyasskid - Captain
- Posts: 574
- Joined: Sat May 14, 2016 3:07 am
Re: Titan two KM capture into Xim4
ive put everything like u said but the xim4 is not getting any inputs and to run the script i put it in slot 1 and put titan two on slot 1 also right?
-
fdg0d - Sergeant Major
- Posts: 83
- Joined: Thu May 12, 2016 3:16 pm
Re: Titan two KM capture into Xim4
You can install the script directly to one of your memory slots, or run it straight from The GPC Script IDE. By selecting the Test and debug Button. It should be a Green Arrow. up near the top.
-
Sillyasskid - Captain
- Posts: 574
- Joined: Sat May 14, 2016 3:07 am
Re: Titan two KM capture into Xim4
i did that but still no inputs on the xim4
-
fdg0d - Sergeant Major
- Posts: 83
- Joined: Thu May 12, 2016 3:16 pm
Re: Titan two KM capture into Xim4
Is this how your setup looks like?
-
Sillyasskid - Captain
- Posts: 574
- Joined: Sat May 14, 2016 3:07 am
Re: Titan two KM capture into Xim4
i had my controller on the 3 dots on xim4 i switched it to the 2 dots the titan two still sends no inputs to the xim4
-
fdg0d - Sergeant Major
- Posts: 83
- Joined: Thu May 12, 2016 3:16 pm
Re: Titan two KM capture into Xim4
also im trying to use it on ps4
-
fdg0d - Sergeant Major
- Posts: 83
- Joined: Thu May 12, 2016 3:16 pm
Re: Titan two KM capture into Xim4
fdg0d wrote:also im trying to use it on ps4
The three dot, or two dot one works for me. Anyways.
Do you have your ps4 controller paired over USB ?
-
Sillyasskid - Captain
- Posts: 574
- Joined: Sat May 14, 2016 3:07 am
Re: Titan two KM capture into Xim4
my controller works fine on both 3 and 2 dots its just the titan two doesnt send anything to the xim4
-
fdg0d - Sergeant Major
- Posts: 83
- Joined: Thu May 12, 2016 3:16 pm
22 posts
• Page 1 of 3 • 1, 2, 3
Who is online
Users browsing this forum: No registered users and 160 guests