Question about sensitivity
5 posts
• Page 1 of 1
Question about sensitivity
I understand the basic commands for LS and RS sensitivity such as
sensitivity(XB360_LX, NOT_USE, 200);
sensitivity(XB360_LY, NOT_USE, 200);
sensitivity(XB360_RX, NOT_USE, 200);
sensitivity(XB360_RY, NOT_USE, 200);
where NOT_USE = midpoint sensitivity, however is there another way to further enhance the sensitivity settings for the LS and RS sticks?
sensitivity(XB360_LX, NOT_USE, 200);
sensitivity(XB360_LY, NOT_USE, 200);
sensitivity(XB360_RX, NOT_USE, 200);
sensitivity(XB360_RY, NOT_USE, 200);
where NOT_USE = midpoint sensitivity, however is there another way to further enhance the sensitivity settings for the LS and RS sticks?
-
D Dark - Staff Sergeant
- Posts: 14
- Joined: Thu Aug 28, 2014 12:52 am
- Location: EAST COAST
Re: Question about sensitivity
You can use the deadzone operation:
http://www.consoletuner.com/kbase/i_o_f ... m#deadzone
It removes the "deadzone" of the analog sticks, use it after the sensitivity operations.
Example of use:
http://www.consoletuner.com/kbase/i_o_f ... m#deadzone
It removes the "deadzone" of the analog sticks, use it after the sensitivity operations.
Example of use:
- Code: Select all
// SQUARE Shape Deadzone
deadzone(PS3_RX, PS3_RY, 20, 22);
// CIRCLE Shape Deadzone
deadzone(XB360_RX, XB360_RY, DZ_CIRCLE, 26);
ConsoleTuner Support Team
-
J2Kbr - General of the Army
- Posts: 20323
- Joined: Tue Mar 18, 2014 1:39 pm
Re: Question about sensitivity
I will try that, I also read an article yesterday about a controller which allows you to increase the sensitivity of LS and RS. It talks about decreasing/increasing the range of the LS and RS, I was wondering if the TITAN ONE can do the same? If you have free time check out the article: http://www.marauderzstuff.com/PermaLink ... 8facf.aspx
-
D Dark - Staff Sergeant
- Posts: 14
- Joined: Thu Aug 28, 2014 12:52 am
- Location: EAST COAST
Re: Question about sensitivity
First off, that doesn't actually increase any range. The controller still only reports 0-100. You can not make it go beyond factory spec in that regard. What it describes is changing the operating range to a percentage of what it was. Yes, the Titan can do that. See the usage of the sensitivity command.
The script would be tailored to the % you want to use, but you would use something akin to:
I think what you want to do is use this command after all - just find a midpoint that performs as you wish or find a different multiplier to use at the end. This hardware works by intercepting the commands between the console and the controller. As the console won't take a command for a value above (or below) operating levels, it ignores them.
The script would be tailored to the % you want to use, but you would use something akin to:
- Code: Select all
main {
sensitivity(XB1_RY, 50, 125); // This retains the midpoint of the stick at 50 and multiplies the input by 1.25
}
I think what you want to do is use this command after all - just find a midpoint that performs as you wish or find a different multiplier to use at the end. This hardware works by intercepting the commands between the console and the controller. As the console won't take a command for a value above (or below) operating levels, it ignores them.
-
Sitava - Corporal
- Posts: 5
- Joined: Sat Jul 19, 2014 9:41 am
Re: Question about sensitivity
sounds good bro, thanks
-
D Dark - Staff Sergeant
- Posts: 14
- Joined: Thu Aug 28, 2014 12:52 am
- Location: EAST COAST
5 posts
• Page 1 of 1
Return to GPC1 Script Programming
Who is online
Users browsing this forum: No registered users and 142 guests