anti-recoil for xim apex
Moderator: antithesis
7 posts
• Page 1 of 1
anti-recoil for xim apex
there was a new FW update for the Apex, it allows you to turn SAB off, I use a navy so I run off. if SAB's set to off theirs no resting value at all, it go's to zero every time when in the T2 device monitor. my question is on the anti-recoil scripts with resting value, do I set it to 0 then? I'm pretty sure I do.
-
slickrick6922 - Master Sergeant
- Posts: 35
- Joined: Fri Dec 07, 2018 2:14 am
Re: anti-recoil for xim apex
slickrick6922 wrote:there was a new FW update for the Apex, it allows you to turn SAB off, I use a navy so I run off. if SAB's set to off theirs no resting value at all, it go's to zero every time when in the T2 device monitor. my question is on the anti-recoil scripts with resting value, do I set it to 0 then? I'm pretty sure I do.
Antirecoil scripts works on the right stick
SAB only affects the left stick, so ON or OFF it doesn't matter.
-
alanmcgregor - Major
- Posts: 995
- Joined: Tue Mar 27, 2018 8:38 am
Re: anti-recoil for xim apex
alanmcgregor wrote:SAB only affects the left stick, so ON or OFF it doesn't matter.
This is incorrect.
SAB effects both sticks, not just the left.
Its not hard to notice, simply look over at the device monitor with SAB on, and then again with it off.
SAB Off
SAB On
When ever the Apex assumes the stick has entered the deadzone, a random value less than 6% gets assigned to each axis.
Ever since the Apex launched its always done this. This is because SAB had always been enabled. Its the main reason why all of the anti-recoil scripts have the stick-noise setting. Its to compensate for the deadzone values that apex adds.
Its only now with the new firmware, we have the option to turn it off completely.
-
DontAtMe - Captain
- Posts: 502
- Joined: Tue Oct 02, 2018 4:49 am
Re: anti-recoil for xim apex
yeah check it out for you self in device monitor, the same stick used on the controller[right stick] will not rest at a value of 0 with sab on, turn it off and it zeros perfect every time.
Last edited by slickrick6922 on Sun Jun 30, 2019 8:55 am, edited 1 time in total.
-
slickrick6922 - Master Sergeant
- Posts: 35
- Joined: Fri Dec 07, 2018 2:14 am
Re: anti-recoil for xim apex
yeah , sab's affecting my right stick, check it out for your self in the device monitor.alanmcgregor wrote:slickrick6922 wrote:there was a new FW update for the Apex, it allows you to turn SAB off, I use a navy so I run off. if SAB's set to off theirs no resting value at all, it go's to zero every time when in the T2 device monitor. my question is on the anti-recoil scripts with resting value, do I set it to 0 then? I'm pretty sure I do.
Antirecoil scripts works on the right stick
SAB only affects the left stick, so ON or OFF it doesn't matter.
-
slickrick6922 - Master Sergeant
- Posts: 35
- Joined: Fri Dec 07, 2018 2:14 am
Re: anti-recoil for xim apex
They might change something about SAB, because in its earlier versions only left stick was altered (this coming from OBsIV).
Well is great that now can be fully turned off
Well is great that now can be fully turned off
-
alanmcgregor - Major
- Posts: 995
- Joined: Tue Mar 27, 2018 8:38 am
7 posts
• Page 1 of 1
Return to XIM Apex, XIM4, XIM Edge with Titan devices
Who is online
Users browsing this forum: No registered users and 62 guests