ConsoleTuner

Hardware needed:

- A Titan One dongle

- A bluetooth dongle (I have an Asus USB-BT400 and a BT that I ordered with the Titan One dongle and both work fine).

- An original nintendo wiimote (both the old one and the new one with the motion plus work), nunchuck and wii(u) sensorbar (powered by a wii(u) or a "wireless" (i.e. no power wire to the wii(u)) sensorbar powered by batteries or ac/dc adapter).

- A windows PC for (one time) uploading (or configuring buttonmapping) wiimote script(s) into the Titan One dongle.

- For XB1 only: you always need also a windows PC running the MaxAIM DI program while using the Titan One dongle and wiimote. For PS4 you can use this as well or use the partial support setting in the titan one so you do not need a PC.

Additionally needed:
Gtuner software (see downloads) to install buttonmapping scripts from the online library to the Titan One dongle. The scripts are just text files that you can open with gtuner or notepad to alter them to your needs.

Installation:
The Titan One dongle has one usb output (see left side of picture) that you put in your gaming console.
It has two usb inputs: one normal usb port for the bt dongle (see right side of picture) and one mini usb on the middle side to connect to your PC via a usb cable (see top side of picture).



-1- Connect the Titan One via the mini usb cable to your PC.

-2- Run the gtuner software, select the "ONLINE LIBRARY" page, select the "WIIMOTE" category, select the wiimote script from the online library (for example the call of duty script), press the download button and save the file as cod.gpc (for example).

-3- In gtuner open the "PROGRAMMER" page and drag the cod.gpc displayed on the left of the screen to the right hand side of the screen and drop it into slot 1.

-4- In gtuner press the "PROGRAM DEVICE" button.

-5- Put the Blue Tooth dongle into Titan One dongle.


Running:
-1- Turn on your sensorbar.

-2- Insert the Titan One dongle in your gaming console.

-3- Press the red sync button of the wiimote (inside the battery compartment).

-4- Press the button on the dongle until its led display it shows 1 (slot 1).

-5- Play!

Here's my setup (ps3 + titan one + blue tooth + wiimote + nunchuck + sensorbar + call of duty + battlefield)

Some links to setup of the wiimote and the titan one with a PS4/PS3/xbox360/xboxOne.

http://www.consoletuner.com/kbase/conne ... tion_4.htm

http://www.consoletuner.com/kbase/device_options.htm

http://www.consoletuner.com/kbase/wiimo ... nsions.htm

The sync button (red button on the back of wiimote controller) is used to connect the wiimote to the bluetooth dongle that is inserted in the titan one dongle.

Quick setup:

Get a wiimote + nunchuck + powered sensorbar + titan one + bluetooth (BT) adapter

You have to use gtuner on a pc and connect the titan one to it via usb to once install the cod script and set the following settings:
V enable PS4 partial crossover support

V Inframe Out V 1ms response V DS4 BT Boost



Start the ps4 with the titan one dongle in the PS4 (with the BT adapter in it) press the red connect button of the wiimote, select slot e.g. 1 for your cod script and GO PLAY

Every 10 minutes you see the controller disconnect and immediately reconnect (takes less than 1 second)

The new titan device (ETA Q1 2016) will have BT built in and more than 1 usb input (so the ps4 controller can remain plugged in all time and there's no more auto disconnect/reconnect after 10 minutes)